Ergonomics and health

Laptop coaster preventing heating of lap and improving laptop airflow.

Because of their small and flat keyboard and trackpad pointing devices, prolonged use of laptops can cause RSI.^[35] Usage of ergonomic keyboards and pointing devices is recommended to prevent injury when working for long periods of time; they can be connected to a laptop easily by USB or via a docking station. Some health standards require ergonomic keyboards at workplaces.

The integrated screen often causes users to hunch over for a better view, which can cause neck or spinal injuries. A larger and higher-quality external screen can be connected to almost any laptop to alleviate that and to provide additional "screen estate" for more productive work.

A study by State University of New York researchers found that heat generated from laptops can raise the temperature of the scrotum, potentially putting sperm count at risk. The small study, which included little more than two dozen men aged 13 to 35, found that the sitting position required to balance a laptop can raise scrotum temperature by as much as 2.1 °C (3.8 °F). Heat from the laptop itself can raise the temperature by another 0.7 °C (1.4 °F), bringing the potential total increase to 2.8 °C (5.2 °F). However, further research is needed to determine whether this directly affects sterility in men.^[36]

A common practical solution to this problem is to place the laptop on a table or desk. Another solution is to obtain a cooling unit for the laptop, these units are usually USB powered consist of a hard thin plastic case housing 1, 2 or 3 cooling fans (the whole thing is designed to sit under a laptop) which results in the laptop remaining cool to the touch, and greatly reduces laptop heat generation. There are several companies which make these coolers.

Heat from using a laptop on the lap can also cause skin discoloration on the thighs.^[37]

Read more...

Rugged Laptop

A Panasonic Toughbook.

A rugged (or ruggedized) laptop is designed to reliably operate in harsh usage conditions such as strong vibrations, extreme temperatures and wet or dusty environments. Rugged laptops are usually designed from scratch, rather than adapted from regular consumer laptop models. Rugged notebooks are bulkier, heavier, and much more expensive than regular laptops^[15], and thus are seldom seen in regular consumer use.

The design features found in rugged laptops include rubber sheeting under the keyboard keys, sealed port and connector covers, passive cooling, superbright displays easily readable in daylight, cases and frames made of magnesium alloys or have a magnesium alloy rollcage^[16] that are much stronger than plastic found in commercial laptops and solid-state storage devices or hard disc drives that are shock mounted to withstand constant vibrations. Rugged laptops are commonly used by public safety services (police, fire and medical emergency), military, utilities, field service technicians, construction, mining and oil drilling personnel. Rugged laptops are usually sold to organizations, rather than individuals, and are rarely marketed via retail channels.

Read more...

Replacement Computer

An Apple 17" MacBook Pro is often used as a desktop replacement.

A desktop replacement computer is a laptop that provides most of the capabilities of a desktop computer, with a similar level of performance. Desktop replacements are usually larger and heavier than standard laptops. They contain more powerful components and numerous ports, and have a 15.4" or larger display. Because of their bulk, they are not as portable as other laptops and their operation time on batteries is typically shorter.^[11]

Some laptops in this class use a limited range of desktop components to provide better performance for the same price at the expense of battery life; in a few of those models, there is no battery at all, and the laptop can only be used when plugged in. These are sometimes called desknotes, a portmanteau of the words "desktop" and "notebook," though the term can also be applied to desktop replacement computers in general.^[12]

The names "Media Center Laptops" and "Gaming Laptops" are also used to describe this class of notebooks.^[10]

Read more...

Software engineering

Jump to: navigation, search

The new Airbus A-380 uses a substantial amount of software to create a "paperless" cockpit.

A typical software engineer's office.

Software engineering is the application of a systematic, disciplined, quantifiable approach to the development, operation, and maintenance of software, and the study of these approaches. That is the application of engineering to software. [1]

The term software engineering first appeared in the 1968 NATO Software Engineering Conference and was meant to provoke thought regarding the current "software crisis" at the time.[2] Since then, it has continued as a profession and field of study dedicated to creating software that is of higher quality, cheaper, maintainable, and quicker to build. Since the field is still relatively young compared to its sister fields of engineering, there is still much work and debate around what software engineering actually is. It has grown organically out of the limitations of viewing software as just programming. Software development is a term sometimes preferred by practitioners in the industry who view software engineering as too heavy-handed and constrictive to the malleable process of creating software.

Yet, in spite of its youth as a profession, the field's future looks bright as Money Magazine and Salary.com rated software engineering as the best job in America in 2006. [3]

Read more...

History of programming

Wired plug board for an IBM 402 Accounting Machine.

The concept of devices that operate following a pre-defined set of instructions traces back to Greek Mythology, notably Hephaestus and his mechanical servants[3]. The Antikythera mechanism was a calculator utilizing gears of various sizes and configuration to determine its operation. The earliest known programmable machines (machines whose behavior can be controlled and predicted with a set of instructions) were Al-Jazari's programmable Automata in 1206.[4] One of Al-Jazari's robots was originally a boat with four automatic musicians that floated on a lake to entertain guests at royal drinking parties. Programming this mechanism's behavior meant placing pegs and cams into a wooden drum at specific locations. These would then bump into little levers that operate a percussion instrument. The output of this device was a small drummer playing various rhythms and drum patterns.[5][6] Another sophisticated programmable machine by Al-Jazari was the castle clock, notable for its concept of variables which the operator could manipulate as necessary (i.e. the length of day and night). The Jacquard Loom, which Joseph Marie Jacquard developed in 1801, uses a series of pasteboard cards with holes punched in them. The hole pattern represented the pattern that the loom had to follow in weaving cloth. The loom could produce entirely different weaves using different sets of cards. Charles Babbage adopted the use of punched cards around 1830 to control his Analytical Engine. The synthesis of numerical calculation, predetermined operation and output, along with a way to organize and input instructions in a manner relatively easy for humans to conceive and produce, led to the modern development of computer programming.

Development of computer programming accelerated through the Industrial Revolution. The punch card innovation was later refined by Herman Hollerith who, in 1896 founded the Tabulating Machine Company (which became IBM). He invented the Hollerith punched card, the card reader, and the key punch machine. These inventions were the foundation of the modern information processing industry. The addition of a plug-board to his 1906 Type I Tabulator allowed it to do different jobs without having to be physically rebuilt. By the late 1940s there were a variety of plug-board programmable machines, called unit record equipment, to perform data processing tasks (card reading). Early computer programmers used plug-boards for the variety of complex calculations requested of the newly invented machines.
Data and instructions could be stored on external punch cards, which were kept in order and arranged in program decks.

The invention of the Von Neumann architecture allowed computer programs to be stored in computer memory. Early programs had to be painstakingly crafted using the instructions of the particular machine, often in binary notation. Every model of computer would be likely to need different instructions to do the same task. Later assembly languages were developed that let the programmer specify each instruction in a text format, entering abbreviations for each operation code instead of a number and specifying addresses in symbolic form (e.g. ADD X, TOTAL). In 1954 Fortran, the first higher level programming language, was invented. This allowed programmers to specify calculations by entering a formula directly (e.g. Y = X*2 + 5*X + 9). The program text, or source, was converted into machine instructions using a special program called a compiler. Many other languages were developed, including ones for commercial programming, such as COBOL. Programs were mostly still entered using punch cards or paper tape. (See computer programming in the punch card era). By the late 1960s, data storage devices and computer terminals became inexpensive enough so programs could be created by typing directly into the computers. Text editors were developed that allowed changes and corrections to be made much more easily than with punch cards.

As time has progressed, computers have made giant leaps in the area of processing power. This has brought about newer programming languages that are more abstracted from the underlying hardware. Although these more abstracted languages require additional overhead, in most cases the huge increase in speed of modern computers has brought about little performance decrease compared to earlier counterparts. The benefits of these more abstracted languages is that they allow both an easier learning curve for people less familiar with the older lower-level programming languages, and they also allow a more experienced programmer to develop simple applications quickly. Despite these benefits, large complicated programs, and programs that are more dependent on speed still require the faster and relatively lower-level languages with today's hardware. (The same concerns were raised about the original Fortran language.)

Throughout the second half of the twentieth century, programming was an attractive career in most developed countries. Some forms of programming have been increasingly subject to offshore outsourcing (importing software and services from other countries, usually at a lower wage), making programming career decisions in developed countries more complicated, while increasing economic opportunities in less developed areas. It is unclear how far this trend will continue and how deeply it will impact programmer wages and opportunities.

Read more...

Infection strategies

In order to replicate itself, a virus must be permitted to execute code and write to memory. For this reason, many viruses attach themselves to executable files that may be part of legitimate programs. If a user tries to start an infected program, the virus' code may be executed first. Viruses can be divided into two types, on the basis of their behavior when they are executed. Nonresident viruses immediately search for other hosts that can be infected, infect these targets, and finally transfer control to the application program they infected. Resident viruses do not search for hosts when they are started. Instead, a resident virus loads itself into memory on execution and transfers control to the host program. The virus stays active in the background and infects new hosts when those files are accessed by other programs or the operating system itself.

Read more...

The World Wide Web

Graphic representation of a minute fraction of the WWW, demonstrating hyperlinks

For more details on this topic, see World Wide Web.

Graphic representation of a minute fraction of the WWW, demonstrating hyperlinks

Many people use the terms Internet and World Wide Web (or just the Web) interchangeably, but, as discussed above, the two terms are not synonymous.

The World Wide Web is a huge set of interlinked documents, images and other resources, linked by hyperlinks and URLs. These hyperlinks and URLs allow the web servers and other machines that store originals, and cached copies of, these resources to deliver them as required using HTTP (Hypertext Transfer Protocol). HTTP is only one of the communication protocols used on the Internet.

Web services also use HTTP to allow software systems to communicate in order to share and exchange business logic and data.

Software products that can access the resources of the Web are correctly termed user agents. In normal use, web browsers, such as Internet Explorer, Firefox and Apple Safari, access web pages and allow users to navigate from one to another via hyperlinks. Web documents may contain almost any combination of computer data including graphics, sounds, text, video, multimedia and interactive content including games, office applications and scientific demonstrations.

Through keyword-driven Internet research using search engines like Yahoo! and Google, millions of people worldwide have easy, instant access to a vast and diverse amount of online information. Compared to encyclopedias and traditional libraries, the World Wide Web has enabled a sudden and extreme decentralization of information and data.

Using the Web, it is also easier than ever before for individuals and organisations to publish ideas and information to an extremely large audience. Anyone can find ways to publish a web page, a blog or build a website for very little initial cost. Publishing and maintaining large, professional websites full of attractive, diverse and up-to-date information is still a difficult and expensive proposition, however.

Many individuals and some companies and groups use "web logs" or blogs, which are largely used as easily updatable online diaries. Some commercial organisations encourage staff to fill them with advice on their areas of specialization in the hope that visitors will be impressed by the expert knowledge and free information, and be attracted to the corporation as a result. One example of this practice is Microsoft, whose product developers publish their personal blogs in order to pique the public's interest in their work.

Collections of personal web pages published by large service providers remain popular, and have become increasingly sophisticated. Whereas operations such as Angelfire and GeoCities have existed since the early days of the Web, newer offerings from, for example, Facebook and MySpace currently have large followings. These operations often brand themselves as social network services rather than simply as web page hosts.

Advertising on popular web pages can be lucrative, and e-commerce or the sale of products and services directly via the Web continues to grow.

In the early days, web pages were usually created as sets of complete and isolated HTML text files stored on a web server. More recently, websites are more often created using content management or wiki software with, initially, very little content. Contributors to these systems, who may be paid staff, members of a club or other organisation or members of the public, fill underlying databases with content using editing pages designed for that purpose, while casual visitors view and read this content in its final HTML form. There may or may not be editorial, approval and security syste

Read more...

Internet protocols

The My Opera Community server rack. From the top, user file storage (content of files.myopera.com), "bigma" (the master MySQL database server), and two IBM blade centers containing multi-purpose machines (Apache front ends, Apache back ends, slave MySQL database servers, load balancers, file servers, cache servers and sync masters).

The complex communications infrastructure of the Internet consists of its hardware components and a system of software layers that control various aspects of the architecture. While the hardware can often be used to support other software systems, it is the design and the rigorous standardization process of the software architecture that characterizes the Internet.

The responsibility for the architectural design of the Internet software systems has been delegated to the Internet Engineering Task Force (IETF).^[9] The IETF conducts standard-setting work groups, open to any individual, about the various aspects of Internet architecture. Resulting discussions and final standards are published in Request for Comments (RFCs), freely available on the IETF web site.

The principal methods of networking that enable the Internet are contained in a series of RFCs that constitute the Internet Standards. These standards describe a system known as the Internet Protocol Suite. This is a model architecture that divides methods into a layered system of protocols (RFC 1122, RFC 1123). The layers correspond to the environment or scope in which their services operate. At the top is the space (Application Layer) of the software application, e.g., a web browser application, and just below it is the Transport Layer which connects applications on different hosts via the network (e.g., client-server model). The underlying network consists of two layers: the Internet Layer which enables computers to connect to one-another via intermediate (transit) networks and thus is the layer that establishes internetworking and the Internet, and lastly, at the bottom, is a software layer that provides connectivity between hosts on the same local link (therefor called Link Layer), e.g., a local area network (LAN) or a dial-up connection. This model is also known as the TCP/IP model of networking. While other models have been developed, such as the Open Systems Interconnection (OSI) model, they are not compatible in the details of description, nor implementation.

The most prominent component of the Internet model is the Internet Protocol (IP) which provides addressing systems for computers on the Internet and facilitates the internetworking of networks. IP Version 4 (IPv4) is the initial version used on the first generation of the today's Internet and is still in dominant use. It was designed to address up to ~4.3 billion (10⁹) Internet hosts. However, the explosive growth of the Internet has led to IPv4 address exhaustion. A new protocol version, IPv6, was developed which provides vastly larger addressing capabilities and more efficient routing of data traffic. IPv6 is currently in commercial deployment phase around the world.

IPv6 is not interoperable with IPv4. It essentially establishes a "parallel" version of the Internet not accessible with IPv4 software. This means software upgrades are necessary for every networking device that needs to communicate on the IPv6 Internet. Most modern computer operating systems are already converted to operate with both versions of the Internet Protocol. Network infrastructures, however, are still lagging in this development.

Read more...

Theoretical computer science

The broader field of theoretical computer science encompasses both the classical theory of computation, and a wide range of other topics that focus on the more abstract, logical and mathematical aspects of computing.

P \rightarrow Q \, \Gamma\vdash x : Int
Mathematical logic Automata theory Number theory Graph theory Type theory Category theory Computational geometry Quantum computing theory

Read more...

Multitasking

Main article: Computer multitasking

While a computer may be viewed as running one gigantic program stored in its main memory, in some systems it is necessary to give the appearance of running several programs simultaneously. This is achieved by having the computer switch rapidly between running each program in turn. One means by which this is done is with a special signal called an interrupt which can periodically cause the computer to stop executing instructions where it was and do something else instead. By remembering where it was executing prior to the interrupt, the computer can return to that task later. If several programs are running "at the same time", then the interrupt generator might be causing several hundred interrupts per second, causing a program switch each time. Since modern computers typically execute instructions several orders of magnitude faster than human perception, it may appear that many programs are running at the same time even though only one is ever executing in any given instant. This method of multitasking is sometimes termed "time-sharing" since each program is allocated a "slice" of time in turn.

Before the era of cheap computers, the principle use for multitasking was to allow many people to share the same computer.

Seemingly, multitasking would cause a computer that is switching between several programs to run more slowly - in direct proportion to the number of programs it is running. However, most programs spend much of their time waiting for slow input/output devices to complete their tasks. If a program is waiting for the user to click on the mouse or press a key on the keyboard, then it will not take a "time slice" until the event it is waiting for has occurred. This frees up time for other programs to execute so that many programs may be run at the same time without unacceptable speed loss.

Read more...

How computers work

Main articles: Central processing unit and Microprocessor

A general purpose computer has four main sections: the arithmetic and logic unit (ALU), the control unit, the memory, and the input and output devices (collectively termed I/O). These parts are interconnected by busses, often made of groups of wires.

The control unit, ALU, registers, and basic I/O (and often other hardware closely linked with these) are collectively known as a central processing unit (CPU). Early CPUs were composed of many separate components but since the mid-1970s CPUs have typically been constructed on a single integrated circuit called a microprocessor.

Control unit

Main articles: CPU design and Control unit

The control unit (often called a control system or central controller) directs the various components of a computer. It reads and interprets (decodes) instructions in the program one by one. The control system decodes each instruction and turns it into a series of control signals that operate the other parts of the computer.^[16] Control systems in advanced computers may change the order of some instructions so as to improve performance.

A key component common to all CPUs is the program counter, a special memory cell (a register) that keeps track of which location in memory the next instruction is to be read from.^[17]

Diagram showing how a particular MIPS architecture instruction would be decoded by the control system.

The control system's function is as follows—note that this is a simplified description, and some of these steps may be performed concurrently or in a different order depending on the type of CPU:

1. Read the code for the next instruction from the cell indicated by the program counter.
2. Decode the numerical code for the instruction into a set of commands or signals for each of the other systems.
3. Increment the program counter so it points to the next instruction.
4. Read whatever data the instruction requires from cells in memory (or perhaps from an input device). The location of this required data is typically stored within the instruction code.
5. Provide the necessary data to an ALU or register.
6. If the instruction requires an ALU or specialized hardware to complete, instruct the hardware to perform the requested operation.
7. Write the result from the ALU back to a memory location or to a register or perhaps an output device.
8. Jump back to step (1).

Since the program counter is (conceptually) just another set of memory cells, it can be changed by calculations done in the ALU. Adding 100 to the program counter would cause the next instruction to be read from a place 100 locations further down the program. Instructions that modify the program counter are often known as "jumps" and allow for loops (instructions that are repeated by the computer) and often conditional instruction execution (both examples of control flow).

It is noticeable that the sequence of operations that the control unit goes through to process an instruction is in itself like a short computer program - and indeed, in some more complex CPU designs, there is another yet smaller computer called a microsequencer that runs a microcode program that causes all of these events to happen.

Read more...

History of computing

Main article: History of computer hardware

The Jacquard loom was one of the first programmable devices.

It is difficult to identify any one device as the earliest computer, partly because the term "computer" has been subject to varying interpretations over time. Originally, the term "computer" referred to a person who performed numerical calculations (a human computer), often with the aid of a mechanical calculating device.

The history of the modern computer begins with two separate technologies - that of automated calculation and that of programmability.

Examples of early mechanical calculating devices included the abacus, the slide rule and arguably the astrolabe and the Antikythera mechanism (which dates from about 150-100 BC). Hero of Alexandria (c. 10–70 AD) built a mechanical theater which performed a play lasting 10 minutes and was operated by a complex system of ropes and drums that might be considered to be a means of deciding which parts of the mechanism performed which actions and when.^[3] This is the essence of programmability.

The "castle clock", an astronomical clock invented by Al-Jazari in 1206, is considered to be the earliest programmable analog computer.^[4] It displayed the zodiac, the solar and lunar orbits, a crescent moon-shaped pointer travelling across a gateway causing automatic doors to open every hour,^[5][6] and five robotic musicians who play music when struck by levers operated by a camshaft attached to a water wheel. The length of day and night could be re-programmed every day in order to account for the changing lengths of day and night throughout the year.^[4]

The end of the Middle Ages saw a re-invigoration of European mathematics and engineering, and Wilhelm Schickard's 1623 device was the first of a number of mechanical calculators constructed by European engineers. However, none of those devices fit the modern definition of a computer because they could not be programmed.

In 1801, Joseph Marie Jacquard made an improvement to the textile loom that used a series of punched paper cards as a template to allow his loom to weave intricate patterns automatically. The resulting Jacquard loom was an important step in the development of computers because the use of punched cards to define woven patterns can be viewed as an early, albeit limited, form of programmability.

It was the fusion of automatic calculation with programmability that produced the first recognizable computers. In 1837, Charles Babbage was the first to conceptualize and design a fully programmable mechanical computer that he called "The Analytical Engine".^[7] Due to limited finances, and an inability to resist tinkering with the design, Babbage never actually built his Analytical Engine.

Large-scale automated data processing of punched cards was performed for the U.S. Census in 1890 by tabulating machines designed by Herman Hollerith and manufactured by the Computing Tabulating Recording Corporation, which later became IBM. By the end of the 19th century a number of technologies that would later prove useful in the realization of practical computers had begun to appear: the punched card, Boolean algebra, the vacuum tube (thermionic valve) and the teleprinter.

During the first half of the 20th century, many scientific computing needs were met by increasingly sophisticated analog computers, which used a direct mechanical or electrical model of the problem as a basis for computation. However, these were not programmable and generally lacked the versatility and accuracy of modern digital computers.

Defining characteristics of some early digital computers of the 1940s (In the history of computing hardware)

Name	First operational	Numeral system	Computing mechanism	Programming	Turing complete
Zuse Z3 (Germany)	May 1941	Binary	Electro-mechanical	Program-controlled by punched film stock	Yes (1998)
Atanasoff–Berry Computer (US)	mid-1941	Binary	Electronic	Not programmable—single purpose	No
Colossus (UK)	January 1944	Binary	Electronic	Program-controlled by patch cables and switches	No
Harvard Mark I – IBM ASCC (US)	1944	Decimal	Electro-mechanical	Program-controlled by 24-channel punched paper tape (but no conditional branch)	No
ENIAC (US)	November 1945	Decimal	Electronic	Program-controlled by patch cables and switches	Yes
Manchester Small-Scale Experimental Machine (UK)	June 1948	Binary	Electronic	Stored-program in Williams cathode ray tube memory	Yes
Modified ENIAC (US)	September 1948	Decimal	Electronic	Program-controlled by patch cables and switches plus a primitive read-only stored programming mechanism using the Function Tables as program ROM	Yes
EDSAC (UK)	May 1949	Binary	Electronic	Stored-program in mercury delay line memory	Yes
Manchester Mark 1 (UK)	October 1949	Binary	Electronic	Stored-program in Williams cathode ray tube memory and magnetic drum memory	Yes
CSIRAC (Australia)	November 1949	Binary	Electronic	Stored-program in mercury delay line memory	Yes

A succession of steadily more powerful and flexible computing devices were constructed in the 1930s and 1940s, gradually adding the key features that are seen in modern computers. The use of digital electronics (largely invented by Claude Shannon in 1937) and more flexible programmability were vitally important steps, but defining one point along this road as "the first digital electronic computer" is difficult (Shannon 1940). Notable achievements include:

EDSAC was one of the first computers to implement the stored program (von Neumann) architecture.

• Konrad Zuse's electromechanical "Z machines". The Z3 (1941) was the first working machine featuring binary arithmetic, including floating point arithmetic and a measure of programmability. In 1998 the Z3 was proved to be Turing complete, therefore being the world's first operational computer.
• The non-programmable Atanasoff–Berry Computer (1941) which used vacuum tube based computation, binary numbers, and regenerative capacitor memory.
• The secret British Colossus computers (1943)^[8], which had limited programmability but demonstrated that a device using thousands of tubes could be reasonably reliable and electronically reprogrammable. It was used for breaking German wartime codes.
• The Harvard Mark I (1944), a large-scale electromechanical computer with limited programmability.
• The U.S. Army's Ballistics Research Laboratory ENIAC (1946), which used decimal arithmetic and is sometimes called the first general purpose electronic computer (since Konrad Zuse's Z3 of 1941 used electromagnets instead of electronics). Initially, however, ENIAC had an inflexible architecture which essentially required rewiring to change its programming.

Several developers of ENIAC, recognizing its flaws, came up with a far more flexible and elegant design, which came to be known as the "stored program architecture" or von Neumann architecture. This design was first formally described by John von Neumann in the paper First Draft of a Report on the EDVAC, distributed in 1945. A number of projects to develop computers based on the stored-program architecture commenced around this time, the first of these being completed in Great Britain. The first to be demonstrated working was the Manchester Small-Scale Experimental Machine (SSEM or "Baby"), while the EDSAC, completed a year after SSEM, was the first practical implementation of the stored program design. Shortly thereafter, the machine originally described by von Neumann's paper—EDVAC—was completed but did not see full-time use for an additional two years.

Nearly all modern computers implement some form of the stored-program architecture, making it the single trait by which the word "computer" is now defined. While the technologies used in computers have changed dramatically since the first electronic, general-purpose computers of the 1940s, most still use the von Neumann architecture.

Microprocessors are miniaturized devices that often implement stored program CPUs.

Computers that used vacuum tubes as their electronic elements were in use throughout the 1950s. Vacuum tube electronics were largely replaced in the 1960s by transistor-based electronics, which are smaller, faster, cheaper to produce, require less power, and are more reliable. In the 1970s, integrated circuit technology and the subsequent creation of microprocessors, such as the Intel 4004, further decreased size and cost and further increased speed and reliability of computers. By the 1980s, computers became sufficiently small and cheap to replace simple mechanical controls in domestic appliances such as washing machines. The 1980s also witnessed home computers and the now ubiquitous personal computer. With the evolution of the Internet, personal computers are becoming as common as the television and the telephone in the household.

In 2005 Nokia started to call its top-line smartphones of the N-series "multimedia computers" and after the launch of the Apple iPhone in 2007, many are now starting to add the smartphone category among "real" computers. In 2008, if the category of smartphones are included in the numbers of computers in the world, the biggest computer maker by units sold, is no longer Hewlett-Packard, but rather Nokia.^{[citation needed]}

Read more...

Computer Science Degrees & Resources Online

Introduction

Computer science is the overarching title attributed to the discipline of utilizing computation and information in computer systems. Whereas computer programmers create source code and use programming language to make software, the computer scientist uses these software applications for practical purposes and to understand and utilize computational systems.

Computer Science Books

To master computer science, you will have to do a lot of reading on the subject. While your specific program may recommend certain computer science books to you, you will do well to read as many of the best computer science books as you can get your hands on. Some good texts to start with include 'The C Programming Language' by Brian W. Kernighan, 'C++ Primer' by Stanley B. Lippman, 'Introduction to Algorithms' by Thomas H. Cormen, 'Introduction to the Theory of Computation' by Michael Sipser and 'Concrete Mathematics, a Foundation for Computer Science' by Ronald L. Graham. Places to find computer science books online include Amazon.com, FreeTechBooks.com and your school library website.

Computer Science Articles And Databases

A terrific source of computer science articles is the Citeseer.Continuity database. This database lists all the most cited articles in computer science from 2006 back to 1990, so you have a great chance of finding the article you need, whether it be for research, information or to verify a theory. The database, is updated on a regular basis.

Online Computer Science Journals

Of course, most of the key computer science articles will be found in leading computer science journals. There is no shortage of computer science journals out there, many of which may be accessible through your school libraryís web page, the web pages of other libraries or through other computer science resources online. Some of these include Artificial Intelligence, Computer Graphics, IEEE Transactions on Evolutionary Computation, the Journal of Web Semantics and Logical Methods in Computer Science.

Read more...

History of Computer

A computer is a machine that manipulates data according to a list of instructions.

The first devices that resemble modern computers date to the mid-20th century (1940–1945), although the computer concept and various machines similar to computers existed earlier. Early electronic computers were the size of a large room, consuming as much power as several hundred modern personal computers(PC). Modern computers are based on tiny integrated circuits and are millions to billions of times more capable while occupying a fraction of the space. Today, simple computers may be made small enough to fit into a wristwatch and be powered from a watch battery. Personal computers, in various forms, are icons of the Information Age and are what most people think of as "a computer"; however, the most common form of computer in use today is the embedded computer. Embedded computers are small, simple devices that are used to control other devices — for example, they may be found in machines ranging from fighter aircraft to industrial robots, digital cameras, and children's toys.

The ability to store and execute lists of instructions called programs makes computers extremely versatile and distinguishes them from calculators. The Church–Turing thesis is a mathematical statement of this versatility: any computer with a certain minimum capability is, in principle, capable of performing the same tasks that any other computer can perform. Therefore, computers with capability and complexity ranging from that of a personal digital assistant to a supercomputer are all able to perform the same computational tasks given enough time and storage capacity.

Read more...

Tracking the IP address

1. Tracking the IP address of a site
To know the IP address of a site, we can ping the site these. How: Go to the command prompt and typing PING WWW.SITUS-THE-DILACAK.COM and press enter. It will appear Ip address site these.

2. Track the location server (a real address) of a site
We can track the location of a server with only the site address the site only. You try to stay open www.domainwhitepages.com enter the IP address was the site or enter the address of the site and you will get info full on the server of these sites are the locations of countries and city.

3. Tracking the IP address opponent's chat
When we use Yahoo messenger, we can actually know the IP address from the opponent we chat. How:
:: Send a file on the opponent we chat.
:: Then go to the Command Prompt (MSDOS) and N-type NETSTAT and press
enter, then the IP address of your opponent chats (which you have the file was sent)
will appear along with the port used for sending files.
:: To know the location of your opponent chat (real address) as it is
on campus or in the cafe where you live in check www.domainwhitepages.com
using the IP address that you get.

Read more...